User Tools

Site Tools


ycsserver:dr1x:dr1x_configuration

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
ycsserver:dr1x:dr1x_configuration [2021/10/05 09:43]
dg9ffm [Wiring of the connection cable]
ycsserver:dr1x:dr1x_configuration [2021/10/05 11:01]
dg9ffm [Configuration of DR1-X]
Line 3: Line 3:
 Unfortunately, the DR1-X repeater does not offer a LAN interface to be able to be connected directly to a network. Furthermore, its internal repeater control does not support DG-ID (System Fusion II).\\ Unfortunately, the DR1-X repeater does not offer a LAN interface to be able to be connected directly to a network. Furthermore, its internal repeater control does not support DG-ID (System Fusion II).\\
 \\ \\
-However, the DR1-X with its [Control I/O] connector offers the option of using an external repeater control, for example an MMDVM modem.\\+However, the DR1-X with its [Control I/O] connector offers the option of using an external repeater control, for example an MMDVM modem. //**(Attention: DR1-XFR not supportet)**//\\
 This expansion can be carried out without interfering with the repeater hardware and turns the dr1-x into a full-fledged mmdvm repeater, which now also supports DG-ID (System Fusion II) and can be connected directly to a YCS server.\\ This expansion can be carried out without interfering with the repeater hardware and turns the dr1-x into a full-fledged mmdvm repeater, which now also supports DG-ID (System Fusion II) and can be connected directly to a YCS server.\\
 \\ \\
Line 35: Line 35:
 Pin assignment of DR1-X [CONTROL I/O] connector:\\ Pin assignment of DR1-X [CONTROL I/O] connector:\\
 \\ \\
-{{:ycsserver:dr1x:dr1x-connector.png?400|}}+{{:ycsserver:dr1x:dr1x-connector.png?400|}}\\
  
 +| **PIN [CONTROL I/O]** | **Description** | **Comment** | **PIN STM32_DVM** | **Description**|
 +|  1  | BASE | Bridge to Pin 5 [CONTROL I/O] | | |
 +|  2  | PTT | |  5  | PTT_R |
 +|  5  | GND | |  8  | GND |
 +|  7  | AF IN | |  2  | TXA_R |
 +|  8  | DISC OUT | |  6  | RXA_R |
 +|  10  | GND | | | |
 +|  11  | EXT port 1 | Bridge to Pin 10 [CONTROL I/O] | | |
 +|  12  | EXT port 2 | Bridge to Pin 15 [CONTROL I/O] with 470 Ohm Resistor | | |
 +|  15  | Switched VCC (13.8 V) | | | |
 +\\
 +\\
 +==== Configuration of DR1-X ====
 +
 +
 +  * Set **"UP LINK"** to **Packet Speed 9600bps**
 +  * Set **"Deviation"** to **WIDE**
 +  * Set **"Remote Operation"** to **ON**
 +\\
 +Further useful information for the configuration of the DR1-X and instructions for level adjustment of the MMDVM board with the help of pistar can be found in the following document:\\   
 + 
 +  * RB_DR-1x setup.pdf
 +    * [[http://www.repeater-builder.com/products/pdfs/RB_DR-1x%20setup.pdf]]  
 +\\
  
  
  
  
ycsserver/dr1x/dr1x_configuration.txt ยท Last modified: 2021/10/05 11:48 by dg9ffm