Differences

This shows you the differences between two versions of the page.

--- ycsserver:dr1x:dr1x_configuration [2021/10/05 09:17]
dg9ffm [Required components]
+++ ycsserver:dr1x:dr1x_configuration [2021/10/05 11:48] (current)
dg9ffm [Recommended configuration of the DR-1X repeater]
@@ Line 3: / Line 3: @@
 Unfortunately, the DR1-X repeater does not offer a LAN interface to be able to be connected directly to a network. Furthermore, its internal repeater control does not support DG-ID (System Fusion II).\\
 \\
-However, the DR1-X with its [Control I/O] connector offers the option of using an external repeater control, for example an MMDVM modem.\\
+However, the DR1-X with its [Control I/O] connector offers the option of using an external repeater control, for example an MMDVM modem. //**(Attention: DR1-XFR not supportet)**//\\
-This expansion can be carried out without interfering with the repeater hardware and turns the dr1-x into a full-fledged mmdvm repeater, which now also supports DG-ID (System Fusion II) and can be connected directly to a YCS server.\\
+This expansion can be carried out without interfering with the repeater hardware and turns the DR1-X into a full-fledged mmdvm repeater, which now also supports DG-ID (System Fusion II) and can be connected directly to a YCS server.\\
 \\
 \\
@@ Line 22: / Line 22: @@
 //Please do not use a VGA screen cable, as not all of the required connections are usually contacted here.//
+\\
+\\
+==== Wiring of the connection cable ====
+Please note the information in the following documents:\\
+  * DR-1 REPEATER, BASE and REMOTE Mode Operations
+    * {{ :ycsserver:dr1x:dr-1_repeater_base_and_remote_mode_operations.pdf |}}
+  * STM32_DVM_USB Schematic
+    * [[http://www.repeater-builder.com/products/pdfs/STM32_DVM_v4.pdf]]
+\\
+\\
+Pin assignment of DR1-X [CONTROL I/O] connector:\\
+\\
+{{:ycsserver:dr1x:dr1x-connector.png?400|}}\\
+| **PIN [CONTROL I/O]** | **Description** | **Comment** | **PIN STM32_DVM** | **Description**|
+|  1  | BASE | Bridge to Pin 5 [CONTROL I/O] | | |
+|  2  | PTT | |  5  | PTT_R |
+|  5  | GND | |  8  | GND |
+|  7  | AF IN | |  2  | TXA_R |
+|  8  | DISC OUT | |  6  | RXA_R |
+|  10  | GND | | | |
+|  11  | EXT port 1 | Bridge to Pin 10 [CONTROL I/O] | | |
+|  12  | EXT port 2 | Bridge to Pin 15 [CONTROL I/O] with 470 Ohm Resistor | | |
+|  15  | Switched VCC (13.8 V) | | | |
+\\
+\\
+==== Configuration of DR1-X ====
+  * Set **"UP LINK"** to **Packet Speed 9600bps**
+  * Set **"Deviation"** to **WIDE**
+  * Set **"Remote Operation"** to **ON**
+\\
+Further useful information for the configuration of the DR1-X and instructions for level adjustment of the MMDVM board with the help of pistar can be found in the following document:\\
+  * RB_DR-1x setup.pdf
+    * [[http://www.repeater-builder.com/products/pdfs/RB_DR-1x%20setup.pdf]]
+\\

C4FM Multiprotocol Server

User Tools

Site Tools

Differences

Page Tools