User Tools

Site Tools


ycsserver:dr1x:dr1x_configuration

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
ycsserver:dr1x:dr1x_configuration [2021/10/05 10:01]
dg9ffm [Wiring of the connection cable]
ycsserver:dr1x:dr1x_configuration [2021/10/05 11:48] (current)
dg9ffm [Recommended configuration of the DR-1X repeater]
Line 3: Line 3:
 Unfortunately, the DR1-X repeater does not offer a LAN interface to be able to be connected directly to a network. Furthermore, its internal repeater control does not support DG-ID (System Fusion II).\\ Unfortunately, the DR1-X repeater does not offer a LAN interface to be able to be connected directly to a network. Furthermore, its internal repeater control does not support DG-ID (System Fusion II).\\
 \\ \\
-However, the DR1-X with its [Control I/O] connector offers the option of using an external repeater control, for example an MMDVM modem.\\ +However, the DR1-X with its [Control I/O] connector offers the option of using an external repeater control, for example an MMDVM modem. //**(Attention: DR1-XFR not supportet)**//\\ 
-This expansion can be carried out without interfering with the repeater hardware and turns the dr1-into a full-fledged mmdvm repeater, which now also supports DG-ID (System Fusion II) and can be connected directly to a YCS server.\\+This expansion can be carried out without interfering with the repeater hardware and turns the DR1-into a full-fledged mmdvm repeater, which now also supports DG-ID (System Fusion II) and can be connected directly to a YCS server.\\
 \\ \\
 \\ \\
Line 37: Line 37:
 {{:ycsserver:dr1x:dr1x-connector.png?400|}}\\ {{:ycsserver:dr1x:dr1x-connector.png?400|}}\\
  
-| **PIN [CONTROL I/O]** | **Description** | **Bridge** | **PIN STM32_DVM** | **Description**| +| **PIN [CONTROL I/O]** | **Description** | **Comment** | **PIN STM32_DVM** | **Description**| 
-| 1 | BASE | | **** | **** | ****+  | BASE | Bridge to Pin 5 [CONTROL I/O] | | | 
-| 2 | PTT | | | | 5 | PTT_R |+  | PTT | |  5  PTT_R | 
 +|   | GND | |  8  | GND | 
 +|  7  | AF IN | |  2  | TXA_R | 
 +|  8  | DISC OUT | |  6  | RXA_R | 
 +|  10  | GND | | | | 
 +|  11  | EXT port 1 | Bridge to Pin 10 [CONTROL I/O] | | | 
 +|  12  | EXT port 2 | Bridge to Pin 15 [CONTROL I/O] with 470 Ohm Resistor | | | 
 +|  15  | Switched VCC (13.8 V) | | | |
 \\ \\
 +\\
 +==== Configuration of DR1-X ====
  
 +
 +  * Set **"UP LINK"** to **Packet Speed 9600bps**
 +  * Set **"Deviation"** to **WIDE**
 +  * Set **"Remote Operation"** to **ON**
 +\\
 +Further useful information for the configuration of the DR1-X and instructions for level adjustment of the MMDVM board with the help of pistar can be found in the following document:\\   
 + 
 +  * RB_DR-1x setup.pdf
 +    * [[http://www.repeater-builder.com/products/pdfs/RB_DR-1x%20setup.pdf]]  
 +\\
  
  
  
  
ycsserver/dr1x/dr1x_configuration.1633428094.txt.gz · Last modified: 2021/10/05 10:01 by dg9ffm