C4FM Multiprotocol Server

User Tools

Site Tools

Trace:
ycsserver:dr2x:dr2x_configuration

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
ycsserver:dr2x:dr2x_configuration [2021/03/02 00:05]
dg9ffm [DG-ID configuration of the DR-2X] 		ycsserver:dr2x:dr2x_configuration [2022/05/29 08:19] (current)
dg9ffm [Network configuration of the DR-2X]
Line 1: Line 1:
 ===== Recommended configuration of the DR-2X repeater ===== ===== Recommended configuration of the DR-2X repeater =====
  
-After the basic configuration of the DR-2X repeater (uplink and downlink frequencies, transmission power, Callsign and more ...) it can now be connected to a ycs server. The following article describes a recommended configuration for the connection.\\+After the basic configuration of the DR-2X repeater (uplink and downlink frequencies, transmission power, Callsign and more ...) it can now be connected to a ycs server. The following article describes a recommended configuration for the ycs-server connection.\\
 \\ \\
 \\ \\
Line 17: Line 17:
   * Use "Write to Device..." to write configuration to the repeater   * Use "Write to Device..." to write configuration to the repeater
  
-  * //The IMRS communicates with the LAN-01A via specified port 21110 (default). DO NOT CHANGE the “21110” UDP port setting. Also you should set the router firewall to open the UDP port “21110”.When using a router to connect the PC to the Internet, the UDP port must go through the router as well; however, communications using this port is generally prohibited on commercially available routers in the default setting.Therefore, if you are using a router, make sure that the port is “open” for passing UDP traffic.//+  * //The IMRS communicates with the LAN-01A via specified port 21110 (default). DO NOT CHANGE the “21110” UDP port setting. Also you should set the router firewall to open the UDP port “21110”.When using a router to connect the PC to the Internet, the UDP port must go through the router as well; however, communications using this port is generally prohibited on commercially available routers in the default setting.Therefore, if you are using a router, make sure that the port is “open” for passing UDP traffic inbound and outbound.//
  
   * On “Destination Repeater's Information” screen, click the button "001". The “Destination Repeater Setting” screen appears.   * On “Destination Repeater's Information” screen, click the button "001". The “Destination Repeater Setting” screen appears.
Line 24: Line 24:
  
   * Enter the IP address of the desired YCS server   * Enter the IP address of the desired YCS server
 +    *  //for example://
 +      * //using Internet: **185.228.139.209** = YCS262 (DE C4FM Germany)//
 +      * //using Hamnet: **44.148.237.4** = YCS262 (DE C4FM Germany)//
 +
 +
  
   * Use "Write to Device..." to write configuration to the repeater   * Use "Write to Device..." to write configuration to the repeater
Line 29: Line 34:
 ==== DG-ID configuration of the DR-2X ==== ==== DG-ID configuration of the DR-2X ====
  
 +// => Please follow the instructions carefully so that correct operation is possible with the correct configuration.// \\
 +\\
 The next step is to configure the repeater's own DG-ID (01) and the desired DG-ID's to be connected to the YCS server.\\ The next step is to configure the repeater's own DG-ID (01) and the desired DG-ID's to be connected to the YCS server.\\
  
ycsserver/dr2x/dr2x_configuration.1614643533.txt.gz · Last modified: 2021/03/02 00:05 by dg9ffm

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki