User Tools
ycsserver:dr2x:dr2x_configuration
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
ycsserver:dr2x:dr2x_configuration [2021/03/01 23:17] dg9ffm [Information to the YCS server sysop] |
ycsserver:dr2x:dr2x_configuration [2022/05/29 08:19] (current) dg9ffm [Network configuration of the DR-2X] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ===== Recommended configuration of the DR-2X repeater ===== | ===== Recommended configuration of the DR-2X repeater ===== | ||
| - | After the basic configuration of the DR-2X repeater (uplink and downlink frequencies, | + | After the basic configuration of the DR-2X repeater (uplink and downlink frequencies, |
| \\ | \\ | ||
| \\ | \\ | ||
| Line 17: | Line 17: | ||
| * Use "Write to Device..." | * Use "Write to Device..." | ||
| - | * //The IMRS communicates with the LAN-01A via specified port 21110 (default). DO NOT CHANGE the “21110” UDP port setting. Also you should set the router firewall to open the UDP port “21110”.When using a router to connect the PC to the Internet, the UDP port must go through the router as well; however, communications using this port is generally prohibited on commercially available routers in the default setting.Therefore, | + | * //The IMRS communicates with the LAN-01A via specified port 21110 (default). DO NOT CHANGE the “21110” UDP port setting. Also you should set the router firewall to open the UDP port “21110”.When using a router to connect the PC to the Internet, the UDP port must go through the router as well; however, communications using this port is generally prohibited on commercially available routers in the default setting.Therefore, |
| * On “Destination Repeater' | * On “Destination Repeater' | ||
| Line 24: | Line 24: | ||
| * Enter the IP address of the desired YCS server | * Enter the IP address of the desired YCS server | ||
| + | * //for example:// | ||
| + | * //using Internet: **185.228.139.209** = YCS262 (DE C4FM Germany)// | ||
| + | * //using Hamnet: **44.148.237.4** = YCS262 (DE C4FM Germany)// | ||
| + | |||
| + | |||
| * Use "Write to Device..." | * Use "Write to Device..." | ||
| Line 29: | Line 34: | ||
| ==== DG-ID configuration of the DR-2X ==== | ==== DG-ID configuration of the DR-2X ==== | ||
| + | // => Please follow the instructions carefully so that correct operation is possible with the correct configuration.// | ||
| + | \\ | ||
| The next step is to configure the repeater' | The next step is to configure the repeater' | ||
| Line 49: | Line 56: | ||
| {{: | {{: | ||
| - | * Tap on the "DG-ID" | + | * Tap on the [DG-ID] field and set " |
| - | * Tap on the "Down Link" | + | * Tap on the [Down Link] field and activate " |
| - | * Tap twice on the "Name" | + | * Tap twice on the [Name] field and configure repeaters callsign. |
| - | * Tap "BACK" | + | * Tap [BACK] to go back to DG-ID List screen |
| {{: | {{: | ||
| + | * Tap on the [RPT Group DG-ID] field | ||
| + | |||
| + | * Tap [EDIT] and and write **00** in the field | ||
| + | |||
| + | * Tap [BACK] twice to go back to DG-ID List screen | ||
| \\ | \\ | ||
| In the next step, the DG-IDs are configured which should be connected to the ycs server. It is possible to configure all DG-ID (02-99).\\ | In the next step, the DG-IDs are configured which should be connected to the ycs server. It is possible to configure all DG-ID (02-99).\\ | ||
| Line 117: | Line 129: | ||
| After the DR-2X has now been successfully connected to the YCS, it will now appear on the dashboard.\\ | After the DR-2X has now been successfully connected to the YCS, it will now appear on the dashboard.\\ | ||
| Please contact the YCS server sysop so that he can enter any missing information about the new repeater.\\ | Please contact the YCS server sysop so that he can enter any missing information about the new repeater.\\ | ||
| - | |||
| - | ---- | ||
| //You can find the contact email on the dashboard of the YCS (SITE-INFO). | //You can find the contact email on the dashboard of the YCS (SITE-INFO). | ||
| //\\ | //\\ | ||
| + | \\ | ||
| + | The following information is required:\\ | ||
| + | * Repeater Callsign | ||
| + | * Name of the location //(e.g. Bad Mergentheim)// | ||
| + | * QTH-Locator 6-digit //(e.g. JN49VM)// | ||
| + | * RX-Frequency in Hz //(e.g. 431962500)// | ||
| + | * TX-Frequency in Hz //(e.g. 439562500)// | ||
| + | \\ | ||
| + | \\ | ||
| + | All DG-IDs (Group DG-ID) configured in the DR-2X repeater are now statically (fixed) booked on the YCS server. Especially with many configured DG-IDs, there is a desire to activate some only when required (on demand).\\ | ||
| + | |||
| + | The YCS server sysop has the option to configure all DG-IDs of the DR-2X connection on demand and also to activate your preferred DG-IDs statically if desired. | ||
| + | Please tell him which DG-IDs you would like to have static (fixed) activated.\\ | ||
| + | \\ | ||
| + | With this function it is possible to configure all DG-ID (02-99) in the DR-2X that they work with the YCS server. On the DR-2X only the traffic of the statically (fixed) activated DG-IDs can be heard. | ||
| + | All other DG-IDs can be activated by the user on demand by simply sending in the corresponding DG-ID. This DG-ID is then automatically booked dynamically on the YCS server for 10 minutes. This DG-ID deactivates itself automatically after 10 minutes of non-use, or can also be deactivated prematurely by the user by briefly sending it in DG-ID 90. | ||
| + | |||
ycsserver/dr2x/dr2x_configuration.1614640664.txt.gz · Last modified: 2021/03/01 23:17 by dg9ffm
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
